Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - racerxx

Pages: [1] 2 3 ... 19
1
The Place / Re: how often you change the oil in the 4 stroke
« on: Today at 06:20:12 PM »
Oils cheap engines are expensive.... every 5 hours when not racing or after every race weekend. I need to change my riding style I keep tearing up clutches still ride like I'm on a two stroke.

2
The Place / Helmet Cams ??
« on: April 10, 2019, 08:06:16 PM »
I've been using a Go Pro for years. or should I say my son has, which model helmet cams offer the most for the money and what is everyone using these days? I like the newer features with GPS, segment times, speed and elevation.

3
The Place / Re: So that's a first ...SRA GP
« on: April 03, 2019, 06:15:00 PM »
They always have a nice layout and I usually ride whatever race they hold early 40+ or 50+. You end up with more seat time than any day of moto and you're done before 12:00. My friends are kicking my ass out there right now need to pick up the pace.

4
The Place / Re: So that's a first ...SRA GP
« on: April 03, 2019, 10:23:54 AM »
50+Maginum  Novice or whatever they call it

5
The Place / Re: April's fool or for real??
« on: April 02, 2019, 04:36:27 PM »
Swap could hardly keep a straight face

6
The Place / So that's a first ...SRA GP
« on: April 02, 2019, 02:50:47 PM »
I ran the SRA GP this weekend on the first lap someone went down in the sand in front of me and I had nowhere to go I managed to miss running him over but went down myself. When I picked up my bike the Clutch lever had punched through my handguard and wouldn't allow the clutch to release fully it took me 2 minutes to pull them apart and get going again.... frustrating .... Just when you think you've seen it all. I'm really enjoying these GP's, needed to mix it up after so many years of just moto. I'll be trying to catch Desto this weekend out at 29 Palms for the Big Six.

8
The Place / Re: LACR VET track rental 03/29 (Friday)
« on: March 15, 2019, 12:40:43 PM »
This was from last month. I'm pretty sure the layout is the same.

https://www.youtube.com/watch?v=BC77zpqsPlY

9
The Place / Re: Swap Moto Race Series
« on: March 11, 2019, 08:01:47 PM »
Nice article Wayne ...... 500 entries holy cow congrats Swap on the series kick off

10
Videos Gallery / Re: Cahuilla Creek: 125 Action (So turn up the volume!)
« on: January 06, 2019, 04:00:26 PM »
Make that 125 sing... nice ride ....after watching this I need to get down to Chauilla again

11
Videos Gallery / Santa 2018 Happy Holidays
« on: December 25, 2018, 12:41:21 PM »
Justin happy to get his bike back Just in time for the holidays


https://www.instagram.com/p/Br0qileBKyg/


12
MX tech talk / Re: 16' YZ450 turning
« on: August 29, 2018, 08:36:30 PM »
I have a 2015 YZ450 with a Dubach relocation kit not sure how much the kit helped because i was constantly searching to get it to turn without getting head shake in the fast sections. I'm staying with 105mm SAG, fork height about 3mm (5mm was suggested) and I run a little stiffer on my fork compression. I ride a lot at LACR and Cal City MX and this set up works well at both tracks. I didn't touch anything for Glen Helen this weekend and was really happy.

racerxx, you run the stock 22mm clamps? How bout a Rad lowering kit?

Just saw this a little slow with the reply. I have the stock triple clamps haven't tested any other offset.  I installed the radiator lowering kit TWICE the lowering brackets break pretty easy when you have a get off. I rode gronjo71's stock 14 YZ450 and didn't notice much difference between his and mine I think for me it was more about learning how to get the front wheel waited then all the little tweaks I made. Coming off a YZ250 two stroke it took a while to learn how to make the bike corner. Can't wait to give a 19 a spin maybe this weekend at Cal City MX

13
MX tech talk / Re: YZ450 Gearing
« on: June 26, 2018, 08:59:12 PM »
I went with 13/48 I couldn't find my Vortex sprocket in a 53 tooth. I did replace the and chain guide and cut down the slider slightly to reduce drag. A new chain helps to free things up also. It was too close to Mammoth to start testing chains and sprockets and I was a little worried about how close the chain would be to the cases it's in there pretty tight with a 13 tooth.

14
MX tech talk / Re: YZ450 Gearing
« on: May 30, 2018, 02:42:32 PM »
Having trouble finding a rear 53 in a steel sprocket

15
MX tech talk / Re: YZ450 Gearing
« on: May 28, 2018, 11:04:07 PM »
Nice find might give it a try they were saying the drag on the chain is enough to stand you up in the corners.

Pages: [1] 2 3 ... 19